Essential Plumbing Insights for Bathtub Installation
Essential Plumbing Insights for Bathtub Installation
Blog Article
Every person will have their personal thinking about Installing A Bathtub.
Installing a bathtub isn't exactly rocket science, but it does call for strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is also a reasonably tough job. If the old bathtub is readily easily accessible, the task can move rapidly; if you need to open up a wall surface to remove the old tub as well as place the brand-new tub, the task is much harder. In either instance, the task is within a residence handyman's skills, although you will need an assistant to vacate the old bathtub and set in the new one. Make sure you have qualified on your own for the work and are comfortable attempting it. As opposed to employing a professional to take control of a halfway-completed task, it is far better to think about using one prior to you start. Opportunities are you may require a specialist plumber to make tube connections.
This write-up will certainly aid you set up a brand-new bathtub in your bathroom if you have already bought a new tub as well as do not need to change the setup of your previous water system pipes.
Your devices and product checklist must consist of the following:
Planning for the Installment
Firstly, the supporting structure provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you use all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last placement.
Removing Old Touches
If you need to change old taps with new ones as a part of your setup, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome because of the restricted accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will originate from the pipes. Once the supply pipes have been eliminated, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any old securing compound.
Prior to proceeding to fit the new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Utilizing both wood boards under its feet, put the bath tub in the required placement. The wooden boards are valuable in equally spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four small points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the level as well as changing the feet on the tub till the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Activate the supply of water as well as check all joints and new pipework for leaks and tighten them if essential. Fill up the bath tub and also examine the overflow outlet and the regular electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as securing around the bathtub must wait up until the bath tub has actually been used a minimum of when as this will resolve it into its last placement.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the tap and the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin guaranteeing that the washers are in place between the tap and the sink. Protect the faucet in place with the manufacturer supplied backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The former type must be connected to the faucet finishes initially, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to fracture a stiff seal, creating the water to permeate the wall in between the bathroom as well as the tiling, bring about complications with dampness and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and fittings. They are sold in tubes as well as cartridges, and can sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched paper or soft rope. Remember to always load the bathtub with water prior to sealing, to allow for the movement experienced when the tub remains in use. The sealer can break fairly early if you do not take into consideration this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly offered on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our section about How to Install a Bathtub Yourself. Thanks for spending some time to read our piece of content. Sharing is caring. You won't know, you may be doing someone a favor. Thanks for your time. Kindly check our site back soon.
Reliable help? Dial. Report this page